“This site contains affiliate links for which OEMDTC may be compensated” |
January 18, 2024 NHTSA CAMPAIGN NUMBER: 24V025000
A detached roof molding can create a road hazard for other vehicles, increasing the risk of a crash.
NHTSA Campaign Number: 24V025
Manufacturer Kia America, Inc.
Components STRUCTURE
Potential Number of Units Affected 101,049
Summary
Kia America, Inc. (Kia) is recalling certain 2023-2024 Sportage and 2022-2024 Carnival vehicles. The roof molding may loosen and detach.
Remedy
Dealers will inspect the roof molding and replace or secure it as necessary, free of charge. Owner notification letters are expected to be mailed March 15, 2024. Owners may contact Kia customer service at 1-800-333-4542. Kia’s number for this recall is SC292.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Check if your Kia has a Recall
2023-2024MY Sportage & 2022-2024MY Carnival
Roof Molding
Basis of Safety Defect Determination 573.6(c)(6)
September 25, 2023—October 10, 2023
During routine review of field data, Kia North America (Kia NA) Safety Office identifies increasing number of incidents of loose and missing roof moldings in 2024MY Carnival and 2023MY Sportage vehicles. Kia NA Safety Office escalates issue to SEL for further evaluation, shares preliminary data analysis with Kia Corporation (Kia HQ) and requests further information.
October 11, 2023—November 17, 2023
Due to difficulty in obtaining detached incident roof molding parts, Kia HQ conducts duplication testing on an exemplar Sportage and Carnival vehicle to identify potential failure modes. Kia HQ identifies 1) no interference between roof molding retaining clip and roof panel sealer when sealer applied normally; 2) roof molding does not detach regardless of vehicle speed when retaining clips properly installed; and 3) roof molding detached from both exemplar vehicles when four front retaining clips intentionally and improperly installed and vehicle driven at speeds higher than 90 mph.
Kia HQ shares duplication test results with Kia NA Safety Office and makes request to conduct vehicle inspections to identify condition of incident vehicles.
December 19, 2023—December 21, 2023
Kia NA Safety Office and Kia HQ inspect two (2) Sportage and eight (8) Carnival incident vehicles exhibiting loose or missing roof moldings. Inspections identify interference between roof molding retaining clips and roof panel sealer and/or improperly installed roof molding retaining clips.
January 8, 2024
Kia HQ informs Kia NA Safety Office that it is possible that roof molding may detach from vehicle if the front retaining clips becomes loose (either from interference with roof panel sealer or improper installation) under certain conditions.
January 10, 2024
Kia NA Safety Office updates data analysis across all data sources and identifies 492 unique incidents for 2023-2024MY Sportage: (dates of receipt: 5/23/2022—1/9/2024) and 365 unique incidents for 2022-2024MY Carnival (dates of receipt: 6/21/2021—1/8/2024)]. No crashes or injuries.
January 11, 2024
Kia NA decides to recall certain 2023-2024MY Kia Sportage and certain 2022-2024MY Kia Carnival vehicles. No crashes or injuries.
5 Affected Products
Vehicles
MAKE | MODEL | YEAR |
KIA | CARNIVAL | 2022-2024 |
KIA | SPORTAGE | 2023-2024 |
4 Associated Documents
2023-2024MY Sportage and 2022-2024MY Carnival Roof Molding Chronology
RMISC-24V025-3874.pdf 79.698KB
Recall Acknowledgement
RCAK-24V025-6049.pdf 645.386KB
2022-2024MY Carnival Roof Molding Supplier Information
RMISC-24V025-0910.pdf 70.233KB
Defect Notice 573 Report
RCLRPT-24V025-2374.PDF 214.359KB
Latest Recalls Documents
For the Latest and Most recent Recall Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=24V025&docType=RCL
- Condition: Brand New
- Part Number:872101F001,87210-1F001,87210 1F001
- Contents : 1 x Front LH Roof Molding
- Condition: Brand New
- Color:Black
- Direct Replacement
- Manufacturer Part Number:87214-A2000
- Package Include:1 Pc
- [High Quality Materials]Our car's front windshield strip is made of high-quality rubber material, which is flexible, waterproof, and scratch resistant. Even if used for a long time in hot or rainy weather, it will not crack or twist the edges, and is durable with a long service life.
- [Size]The size of the rubber sealing strip is 16.4FT, and you can freely cut according to the length of your body parts. Suggest a front windshield of approximately 16.4 feet, a rear windshield of approximately 13 feet, a regular small sunroof of approximately 10 feet, and a side triangle window of approximately 3 feet. The above data is for reference only. Please carefully measure the size before purchasing.
- [Function] The sunroof sealing strip is windproof, noise reducing, waterproof and soundproof, effectively reducing wear and noise when doors and windows are opened and closed, making the interior of the car quieter and more comfortable, preventing dust and rainwater from entering your car. It can also reduce noise during driving, providing you and your family with a comfortable driving experience.
- [Easy to Install] 1. Wipe with a cloth to ensure surface cleanliness. If wiping with a damp cloth, ensure installation in dry conditions. If necessary, use a viscosity enhancer to increase viscosity. 2. Tear off the red protective film, press it smoothly onto the edge of the door and window, and then cut off the tape. Do not wash the car within 3.3 days.
- [Applicable] The windshield rubber seal adopts a double-sided adhesive design, and the high-strength adhesive effect is very good. It is equipped with adhesion promoter, which can help the windshield better adhere to the car. This multifunctional car weather strip is more suitable for your windows and body, sealing the gaps between the windows and body, front and rear windshields, sunroof and frame gaps.
- 【Product Quality】The product is the same as the description, very perfect, so that your vehicle works better and uses better.
- 【Specialized factory】We have our own factory with plenty of stock and guaranteed quality.
- 【Good performance】Simple to install, easy to use, in line with the original specifications.
- 【Good service】We have a professional team to provide you with excellent service, so that you can buy with confidence and use with comfort.
- 【Pre-purchase inspection】Please double check the model, size and year of the product before purchase to make sure the product is what you need.
- 【Premium Rubber Material】:The T-shape sunroof seal adoptsdopts durable and excellent quality EPDM rubber material to ensure its soft elasticity and sealing performance, which can maintain the sealing of the sunroof and windshield for a long period of time, even in the strong sunshine and rainstorm and other harsh environments, this rubber edge trim can maintain a very high level of performance to protect the interior of your car.
- 【Perfect Sunroof Seal Strip】:The T-shaped automotive weather stripping can cover the edge of the sunroof and the edges of the front & rear windshields in all directions, providing comprehensive protection. the T-shape design can fit the gap of the sunroof more tightly, which can avoid the intrusion of moisture, dust, dirt, noise, and also play a stabilizing role of the windshield, providing a comfortable and quiet driving environment for you.
- 【Easy Installation and Maintenance】:The rubber seal is adopts strong adhesive backing and T-shape design, double guarantee to snap the groove tightly. Fit the gap naturally and firmly without damaging the paint and glass, without the need for professional and technical personnel to guide.
- 【Universal Fit】:The T-Sunroof Seal is 14mm/0.55" widths and 5M/196.86" lengths for all types of sunroofs or windshields. Whether car, truck or SUV, all can be easily adapted. Our windshield molding can be cut to your desired length, please measure the overall length of your sunroof or windshield sides before purchasing to ensure a satisfying shopping experience.
- 【Keep Car Aesthetically】:The weatherstrip adopts fine craftsmanship and unique design, which not only can provide excellent protection, isolate the penetration of outside air and moisture, reduce noise and vibration conduction, but also the hidden design does not affect the aesthetics of the car, so that your car is more personalized.
- Rear Door, Left Side
- Package Dimensions: 9.398 L x 4.064 H x 59.69 W (centimeters)
- Fit type: Vehicle Specific
- Package Weight: 0.55 pounds
- 【H-Shape】Our windshield cowl rubber seal adopts a unique H-shaped design, which is flexible and clever, and can fit the car front/rear windshield well, forming a perfect closing effect, which enhances the sealing and is not easy to fall off.
- 【Shock Absorbing Seal】The car seal strip for front windshield can have a buffering and sealing effect, which can effectively reduce glass vibration and reduce noise. It can also effectively prevent dust and water, and stably maintaining the air conditioning or heating in the car.
- 【1.7M/ 5.6FT】This front rear windshield panel molding trim strip has a total length of 1.7m/5.6ft, which can be cut to any length according to needs and can be adjusted to fit narrow installations. It is easy to install without any tools.
- 【High Quality Rubber】Our black rubber seals are made of high-quality rubber material, which is safe and not easy to break. It has good flexibility and resistance to compression deformation. It is easy to bend and clean, and can be used in all kinds of weather.
- 【Widely Used】The windshield cowl seal strip for Nissan is suitable for all cars/SUVs/trucks/vans/pickups. It can be used to install on the gaps of front/rear windshields, sunroofs, and rear triangle windows. Just make sure there are no dust or water before installation, just stick it with tape and press it properly.
- Fitment: Compatible with 2010-2011-2012-2013 Kia Soul. Direct aftermarket replacement for part #86180-2K500 & #86170-2K500.
- Feature: Exterior Molding Garnish Windshield Pillar Trim. Color: Black; Made of superior plastic for better performance and durability.
- Condition: It can fix the windshield, play a decorative role, and upgrade the appearance of the car.
- Package includes: 2 pieces (driver & passenger) of pillar trims+all needed clips. No instruction included!!
- Installation: Easy to install, directly bolt-on. Professional installation is highly recommended!
- Precise Fit: Replaces the old weatherstrip directly and equal the quality, each roof drip molding is thoroughly tested to make sure OE fit, Plug and Play, No drilling or cutting required, easy to install
- Durable Rubber Material & Tightness: Made from durable rubber material which is odorless, non-toxic and durable. Reduces wind noise and sway windows at high speeds
- Applicable Models & Years: This weather stripping is compatible with Toyota Prius C 2012 2013 2014 2015 2016 2017 2018 2019, please make sure this moulding trim strip replacement fits your vehicle before order
- Reference Part Number: Left Side 5552-52190, Right Side 75551-52210
- Package Includes: 1 x Left Roof Drip Molding Trim, 1 x Right Roof Drip Molding Trim
- Genuine Kia part that fits your specific vehicle
- Door Reveal Molding
- Part Number: 838602T000
- Manufactured to meet specifications for fit, form, and function
Last update on 2024-07-25 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.
SEOCONTENT-START
2022-2024MY Carnival Roof Molding Supplier Information
Company Name
Saedong (Carnival Roof Molding Supplier)
Country
Republic of Korea
Address
8, Jangansandan 8-Ro, Jangan-Eup
City
Gijang-Gun
State
Foreign State
Zip/Postal Code
62414
Company Contact Information
First Name
Jong wan
Last Name
Bae
Position
Senior Manager
Email
jwbae16@saedong.co.kr
**************************************************************************************************************
OMB Control No.: 2127-0004
Part 573 Safety Recall Report 24V-025
The information contained in this report was submitted pursuant to 49 CFR §573
Manufacturer Name : Submission Date :
Kia America, Inc. JAN 18, 2024 NHTSA Recall No. : 24V-025 Manufacturer Recall No. : SC292 Manufacturer Information :
Manufacturer Name : Kia America, Inc.
Address : 111 Peters Canyon Road
Irvine CA 92606 Company phone : 800-333-4542
Population :
Number of potentially involved : 101,049 Estimated percentage with defect : 1 %
Vehicle Information : Vehicle 1 : 2023-2024 Kia Sportage Vehicle Type : LIGHT VEHICLES Body Style : ALL Power Train : GAS
Descriptive Information : Certain 2023-2024 model year Sportage vehicles manufactured from January 12, 2022 through November 29, 2023 at Kia Georgia (40,426 units). The recall population was determined by a review of vehicle production records. The vehicles subject to this recall were not produced in VIN order. Customers seeking information about their specific vehicle will be referred to Kia’s Customer Care Center or their Kia dealer. Production Dates : JAN 12, 2022 – NOV 29, 2023
VIN Range 1 : Begin : NR End : NR Not sequential Vehicle 2 : 2022-2024 Kia Carnival Vehicle Type : LIGHT VEHICLES Body Style : ALL Power Train : GAS
Descriptive Information : Certain 2022-2024 model year Carnival vehicles manufactured from January 5, 2021 through November 24, 2023 at Kia Autoland Gwangmyeong in Korea (60,623 units). The recall population was determined by a review of vehicle production records. The vehicles subject to this recall were not produced in VIN order. Customers seeking information about their specific vehicle will be referred to Kia’s Customer Care Center or their Kia dealer. Production Dates : JAN 05, 2021 – NOV 24, 2023
VIN Range 1 : Begin : NR End : NR Not sequential Part 573 Safety Recall Report 24V-025 Page 2 Description of Defect :
Description of the Defect : The roof molding may become loose or detach under certain circumstances either due to interference of the roof molding retaining clip(s) with excessive roof panel sealer or due to improper installation of the roof molding during vehicle assembly.
FMVSS 1 : NR FMVSS 2 : NR
Description of the Safety Risk : A detached roof molding can create a road hazard for other vehicles,
increasing the risk of a crash.
Description of the Cause : Interference of the roof molding retaining clip(s) with excessive roof panel sealer and/or improper installation of roof molding during vehicle assembly. Identification of Any Warning
that can Occur : Visible lifting of roof molding(s) and/or noise while driving. Involved Components : Component Name 1 : MOULDING ASSY-ROOF Component Description : Roof Molding Assembly
Component Part Number : Sportage: 87230-P1000 (LH) / 87240-P1000 (RH) Component Name 2 : MOULDING ASSY-ROOF Component Description : Roof Molding Assembly
Component Part Number : Carnival: 87230-R0000 (LH) / 87240-R0000 (RH) Supplier Identification : Component Manufacturer
Name : Wooyoung Industry
Address : (Sportage Roof Molding Supplier)
60, Pyeongdongsandan 1beon-ro Gwangsan-gu Foreign States 62414 Country : Korea, Republic of Chronology : The information contained in this report was submitted pursuant to 49 CFR §573 Part 573 Safety Recall Report 24V-025
Page 3
The information contained in this report was submitted pursuant to 49 CFR §573
See attached document titled “2023-2024MY Sportage and 2022-2024MY Carnival Roof Molding Chronology”.
Description of Remedy :
Description of Remedy Program : All owners of the subject vehicles will be notified by first class mail with
instructions to bring their vehicles to a Kia dealer. Kia dealers will inspect and if necessary, secure/replace the roof moldings(s).
Kia will reimburse owners for repair expenses already incurred pursuant to Kia’s General Reimbursement Plan filed May 10, 2022.
How Remedy Component Differs from Recalled Component : Identify How/When Recall Condition was Corrected in Production :
The roof molding(s) is properly installed and to the extent necessary, contains new retaining clips that prevent interference with excessive roof panel sealer.
Improved retaining clips that do not interfere with excessive roof panel sealer were incorporated into the 2024MY Sportage production on 11/30/2023 and into the 2024MY Carnival production on 12/12/2023. 2024MY Carnival vehicles produced from 11/25/2023 through 12/11/2023 have been held at the port and will be repaired prior to distribution to dealers and thus are excluded from the scope of this recall. In addition, improved assembly processes and training were developed to ensure proper installation of the roof moldings. Recall Schedule :
Description of Recall Schedule : The planned dealer notification begin and end date is March 12, 2024.
The planned owner notification begin and end date is March 15, 2024.
Planned Dealer Notification Date : MAR 12, 2024 – MAR 12, 2024
Planned Owner Notification Date : MAR 15, 2024 – MAR 15, 2024
* NR – Not Reported
**************************************************************************************************************
**************************************************************************************************************
**************************************************************************************************************
SEOCONTENT-END